您的位置: 安全阀网新闻 > 新闻详细

安全阀阀体结合面渗漏

由此快速通道进入阀门产品分类导航,了解 : 上海赛泰泵阀有限公司强大的团队一定能满足您对各类特殊泵阀产品的需求,供您选择最适合您的产品,我们的水泵、阀门技术工程师团队随时恭候您的垂询 !由此快速通道进入阀门产品分类导航,了解 :球阀 闸阀 截止阀 蝶阀 止回阀 柱塞阀 等系列阀门的产品、型号、技术与支持。

原文:
安全阀阀体结合面渗漏 指上下阀体间结合面处的渗漏现象,造成这种漏泄的主要原因有以下几个方面:一是结合面的螺栓紧力不够或紧偏,造成结合面密封不好。 消除方法是调整螺栓紧力,在紧螺栓时一定要按对角把紧的方式进行,最好是边紧边测量各处间隙,将螺栓紧到紧不动为止,并使结合面各处间隙一致。二是阀体结合面的齿形密封垫不符合标准。例如,齿形密封垫径向有轻微沟痕,平行度差,齿形过尖或过坡等缺陷都会造成密封失效。从而使阀体结合面渗漏。在检修时把好备件质量关,采用合乎标准的齿形密封垫就可以避免这种现象的发生。三是阀体结合面的平面度太差或被硬的杂质垫住造成密封失效。对由于阀体结合面的平面度太差而引起阀体结合面渗漏的,消除的方法是将阀门解体重新研磨结合面直至符合质量标准。由于杂质垫住而造成密封失效的,在阀门组装时认真清理结合面避免杂质落入。

“Valve body with the surface leakage ”是由中国安全阀网提供的国际阀门新闻,译文仅供参考。另外,中国安全阀网还提供相关产品搜索: 全启式安全阀封闭式安全阀高压安全阀锅炉安全阀蒸汽安全阀、等。

译文:
Valve body with the surface leakage Between the upper and lower valve leakage at the joint surface, resulting in leakage of the main reasons that the following aspects: First, with the surface of the bolt tightening force is not enough or tight side, resulting in poor seal with the surface. Elimination method is to adjust the bolt tightening force, when the bolt must be tight according to the angle of the way, preferably around the gap measure while the tight side, tighten the bolt does not move to tighten up and make the surface around the gap with the same. Second, the valve seal with the surface of the tooth does not meet the standards. For example, slightly toothed seal radial grooves, parallel to the poor, too sharp or too sloping tooth defects can cause seal failure. So that the valve body with surface leakage. When the good parts in the repair quality, the use of substandard toothed gasket you can avoid this phenomenon. Third, the body surface flatness with poor or live in a hard pad of impurities caused by seal failure. As the body of the combination of poor surface flatness caused by leakage of the valve body with the surface, the method is to eliminate the re-grinding the valve with the disintegration of the surface until it meets quality standards. As a result of impurities live pad seal failure, the valve assembly carefully cleaning the joint surface to avoid falling into impurity.


更多新闻:

原文来源:http://www.1anquanfa.com/

2011-12-29 07:44

返回

上海依耐泵阀有限公司

上海依耐泵阀有限公司隶属中国开维喜集团,组建于 2001 年初,是一家集科研、生产、销售……

依耐安全阀

上海日美阀门制造有限公司

上海日美阀门制造有限公司是在中科院化工冶金所及德国施耐的技术大力支持下组建于02 年初……

日美安全阀

上海一环流体设备有限公司

上海一环流体阀门有限公司一直致力于为推动我国工业自动化的阀门应用尽早全部国产化……

一环安全阀

上海赛泰泵阀有限公司

上海赛泰泵阀有限公司是在国内外泵阀资深专家的大力技术支持下成立于05年,是一家集泵、阀门……

赛泰安全阀

上海丰企阀门有限公司

上海丰企阀门有限公司隶属上海丰企实业发展有限公司阀门事业部,成立于2006年春天,公司……

丰企安全阀

上海天阀实业有限公司

上海天阀实业有限公司是一家具有自营进出口权,成立于2002年2月,由天津阀门厂和上海日泰……

天阀安全阀

上海永鹏阀门有限公司

上海永鹏阀门是隶属上海永鹏机械有限公司的阀门事业部,分为冶金阀门和通用阀门两大生产区……

永鹏安全阀

广告申请

安全阀供应商有意在此发布广告链接的请直接点击……

广告申请

广告热线:021-36525817

技术咨询:021-32010202

友情互联

map

link

product

home

版权所有:中国安全阀网.cn 2008-2009 www.1anquanfa.com 未经授权禁止复制或建立镜像
安全阀生产商和供应商有意在本站刊登广告 请直接联系我们或咨询:021-36525817 传真:021-36525812
中国安全阀网专业为您提供弹簧式安全阀脉冲式安全阀杠杆式安全阀微启式安全阀全启式安全阀封闭式安全阀高压安全阀蒸汽安全阀等各类安全阀型号、价格、技术、新闻及知名安全阀生产商